Abhimanyu Gaonkar

Abhimanyu Gaonkar
Electrical Design Engineer With Four Years Of Experience
Mumbai, Maharashtra, India
Aptitude, Math and Science Tutor, Cricket +22

Profile Snapshot

Abhimanyu is based out of Mumbai & has studied Power System Engineering, ME MTech-Master of Engineering or Technology from Year 2014-2016 in VJTI-Veermata Jijabai Technological Institute, University of Mumbai.

Abhimanyu Gaonkar is Skilled in Aptitude, Math and Science Tutor, Cricket and other talents.

Talents

- Team Leadership
  
  yRank In Mumbai
  
  yRank In Mumbai
- » Compliment
  
  Global yRank
  
  43.52 %
  yTest
  43.52
- Electrical Engineering
  
  yRank In Mumbai
  
  yRank In Mumbai
- » Compliment
  
  Global yRank
  
  27.1 %
  yTest
  27.1
- Internet
  
  yRank In Mumbai
  
  yRank In Mumbai
- » Compliment
  
  Global yRank
  
  56.32 %
  yTest
  56.32
- Math and Science Tutor
  
  yRank In Mumbai
  
  yRank In Mumbai
- » Compliment
  
  Global yRank
  
  87.58 %
  yTest
  87.58

Complete Talent Profile »

Work Experience

Senior Electrical Engineer

Larsen and Toubro Ltd.

Full Time Sep-2016 To present 8 years 7 months

Responsibilities

- System Fault Level calculation and Voltage Regulation calculation
- Calculation of CT & PT parameters for various Applications
- Cable Sizing calculation for HV & LV cables
- Transformer sizing calculation
- Battery Load cycle, Charger & Battery sizing calculation
- UPS with Battery system sizing calculation
- Relay setting calculation & Protection co-ordination curves for LV to MV Switchgears
- Prepared single and three line diagrams, G.A., wiring details, termination details, enclosure selection, busbar sizing & arrangement etc. for Panel Building
- Vendor Drawing Review of Electrical equipments:- LV Switchgear Drawings, Power & Lighting Transformers, UPS with Battery

Electrical Design Engineer

Development Consultants Private Limited

Full Time Aug-2012 To Aug-2014 2 years

Responsibilities

-Preparation of Key Single Line Diagram
-Preparation of Electrical Equipment layouts, Illumination layouts, Cable tray layouts, Earthing & Lightning Protection layouts
-Cable Scheduling and Interconnection Charts
-Development of Logic Diagrams and control Schemes for LV to MV Switchgears
-Protection (Relay) Setting and Co-ordination for LV to MV Switchgears, Generator, Transformer & Motor
-Fault Level Calculations and Voltage Regulation Calculations
-Sizing Calculations of Cable, Transformer, CT/PT, DG Set, Battery and Battery Charger
-Preparation of detailed Tender Specification for Electrical package with respect to BIS, IEEE and other Indian/International standards
-Interdisciplinary Co-ordination
-Preparation of Tender Evaluation Report
-Interfacing with Team Lead/Client for mapping requirement and finalizing specification
-Vendor Documents/Drawing Review

» 4 Projects

Design and Analysis of Converter Transformer

Student at VJTI-Veermata Jijabai Technological Institute

Aug-2015 to Aug-2016

-Blocks higher order harmonics from the input current.
-Extended delta connection is used.
-Six windings on secondary side of transformer.
-This will be used for 36-level converters.
-Simulation models are created on MATLAB and PLEXIM.

Study and Analysis of “Solid State Transformer (SST)”

Student at VJTI-Veermata Jijabai Technological Institute

Aug-2015 to Aug-2016

Solid State Transformer (SST) is widely used in distribution renewable energy resources. SST includes AC-DC rectifier, DC-DC Dual Active Bridge (DAB) converter and AC-DC inverter. In this paper, continuous time average model and dynamic phasor model for combined Rectifier and DAB converter (R-DAB) are developed. Control scheme for R-DAB model is proposed for dynamic phasor based model, in which rectifier and DAB are being individually controlled using PI controller. The effect of controller has been analysed with change in input grid voltage variation. Stability analysis has performed using small signal stability analysis and Lyapunov's criterion. Developed model is verified with simulation in MATLAB/Simulink. Simulation result verifies the proposed modelling technique and controller performance.

Remote Control of Home Appliances

Student at FCRIT-Father Conceicao Rodrigues Institute of Technology

Aug-2012 to Jul-2013

-A device which will switch ON or OFF any home appliances (or load) was made.
-It was made using a sensor, BJT’s, relay and other basic elements.
-By doing some modifications we can make it as burglar alarm or we can control more devices.
-The advantages of this project are maintenance free, compact, simple construction and cheaper.
-Winner of “Mini-Project Competition”, which was organized by Electrical Department.

Design of Testing Bed for Induction Motors

Student at FCRIT-Father Conceicao Rodrigues Institute of Technology

Aug-2011 to Jul-2012

-Study of design of Test bed which will conduct all the tests on Induction Motors.
-Test bed will perform all tests for wide range of power supply with or without Drives from remote location.
-This project consists of applications of Alternator, Transformers, Switchgears, Converters, Invertors, IGBT based variable frequency drive and PLC based automation systems in 3-f power supply.
-Since this project was automated and consists of drives, saving of time and power was possible.
-Study of WinCC and Step-7 softwares and some HMI screens were prepared using same softwares.
-Error list and flowcharts for PLC programming were prepared.

Education

Master of Engineering or Technology

Veermata Jijabai Technological InstituteUniversity of Mumbai

2014-2016 Score83%

Presented a Technical Paper in 48th IEEE-PES North American Power Symposium (NAPS-2016) held at University of Denver, USA and in 6th IEEE International Conference on Power Systems (ICPS-2016) held at Indian Institute of Technology - Delhi. Both the papers are published on IEEE Explore.